• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window is an inconvenience. This could be an opportunity to upgrade to energy-efficient windows or insulated ones to enjoy benefits such as improved comfort, higher resale value and reduced utility bills.

You can do it yourself at less than what it would cost of replacement windows uk to hire an expert. You'll only require the right tools and a few minutes of your time.

Glass

If your single-pane windows are old damaged, cracked or deteriorating replacing them with modern glass that is tempered or insulated can increase energy efficiency and decrease noise while maintaining the historic integrity of older homes. The procedure of replacing windows is easy and can be accomplished by homeowners with basic hand tools. In addition to a replacement double glazing window pane, the following items are needed such as latex glazing putty; pliers, glazier's points and a heat gun for warming the old putty, if necessary. Before beginning, wear gloves and safety goggles as working with broken glass can cause injuries.

Begin by removing any remaining broken pieces of glass. It is recommended to use pliers for this however a flathead could be used as well. After that, use a wood chisel, or putty knife, to remove the rest of the old putty from around the frame and the sash. Take your time and work slowly, taking care not to break the current window sash. It is recommended to work on a sturdy ladder instead of the ground and have someone stand below the sash in order to help hold it in place.

After you've removed all the old putty, it is time to prepare the window frame to fit the new pane. Find the width and the height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to an hardware store or home center and have a piece of stock glass cut to size. You can also cut the glass replacement in windows by yourself if you have the appropriate tools.

After installing the new glass After installing the glass, apply caulking around the edge. This will make the glass weatherproof. Then, you can install a glazier's pointing on the frame's opposite side to secure the pane in place. The points shouldn't be so tight as to cause friction between the frame and sash, but they also should not be too loose.

Before applying the putty to the surface, knead thoroughly until it is soft and free of lumps. Cut it into pencil-sized pieces. The first strip should be glued to the frame's corner. Work from one corner to the next, making sure it is even and smooth.

Glazier's Points

The glazier’s points are small triangular pieces of metal that help secure the glass into the window frame without damaging the delicate surface. It's simple to learn how to use this nefarious tool, and you'll save money on the expense of a professional installation.

After removing the old putty, glazier points as well as any remaining leftovers Clean the frame thoroughly using an utility knife. Lightly sand the wood in the rabbet grooves, if necessary, to smooth rough areas. If you do sand the wood, ensure you protect it with painter's tape to avoid accidental damage.

Take the dimensions of the frame and record precise measurements. Take these dimensions to a hardware store or home center and request that the new pane cut smaller than the frame's opening. This will ensure a tight fit and will allow room for expansion and contraction.

Place the new pane into the frame and push firmly using your hands. Then use the point of your chisel, or the back end of the putty knife to pierce the glazier's points, as shown in Figure 11. When you're done, they should be in line with the top edge of the pane and the shoulders that are raised of the points should be below the rabbet's rim groove.

Apply a small amount of glazing compound on the edges of the glass that has been made and into the rabbet grooves to seal and protect them. Allow this to dry and cure fully.

Install the new window sash after the glazing compound has dried. First, coat the wood with a thick coat of Linseed oil. This will stop the new putty from soaking up moisture and drying out and cracking over time. Use a brush to apply this coat, or the tip of the putty blade. Then, use the chisel on the back of the tool or the back of the putty handle to gently smash the new sash or glazier's tip into the grooves of the rabbet. Repeat this process at intervals of 10 inches around the frame.

Putty

A baseball thrown or a rock thrown in error, or a tree falling can cause a broken or cracked window. Most windows can be replaced by putting in a new piece. The glass replacement for window is held in place by a small metal clip called a glazier's point and putty, which is often called glazing compound. Before you install a new pane, first take out the old one and clean up the area with the help of a rag, the pull-type paint scraper or an abrasive wood chisel. Wear gloves and safety glasses while you do this work. If the window is secured to the frame, you'll need to employ a heat gun in order to soften the adhesive before cutting it loose.

If you are planning to install your original sash, you must remove the molding that supports the old pane. Sand the sash until it is flat and ready to receive new caulk. Once the sash is put back in place then, you can apply a silicone caulk to the glass. This will ensure that it doesn't leak over time or discolor.

Remove the glazing points from the rabbets. These are the grooves on the sash, where the glass is. If they're difficult to cut out, you can try holding the hand tool, such as a heat gun to soften them first. If you're using a heat gun, be careful not to cause damage to the sash or its railings by using the tool too close.

After the old glaze points and putty have been removed make a bed for the new pane. Roll a rope with glazing compound between your fingers and then make it about 1/2 inch thick. Press it into the rabbets, where the glass will be put. The glass must rest against the putty on both sides. If necessary gently tap your glass into the rabbet with your thumb.

If the new pane has a crack then you can seal it with a solvent-based glue or silicone caulk before pressing it into the sash. In other cases, you'll need to apply putty over the crack to form an impervious seal to keep water out. Once the putty is dry clean the oily film off the glass and let it dry completely before you paint. Paint before the putty has completely dried. It won't create a solid seal and could discolor or leak over time.

Paint

You may be concerned about replacing a broken pane of glass. It's true that replacing a single pane glass doesn't need to be expensive if you do it on your own. Even a double-paned window could be replaced for a fraction of what it costs an expert.

If you're working with large glass windows first ensure it is securely attached to the frame. This task can be done relatively easy and fast using the right tools and techniques.

Once you're ready to begin, begin by removing the old window handle replacement pane by removing the glazing points of metal that are attached to it. These are essentially small metal triangles that act as "nails" which hold the window glass replacement in place within the frame of wood. They are placed beneath a layer of glazing putty that transforms into a solid moulded wedge that secures the window in place and hides the edges.

After you have removed the old pane removed, clean up the surrounding frame and wood. Scrape away any paint and sand down the rabbet grooves where the glazing points used to be. These should be sanded to bare wood, to allow you to paint them the same color as the rest of the frame. After the sanding process, apply a coat of flax oil on the wood that is not sanded down to prolong its life.

Next, measure the dimensions of the window opening. You'll need to take vertical and horizontal measurements of the entire opening and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you get a precise size for the new pane. This will also allow for expansion and contraction of the glass during seasons of changes. You can bring these measurements to a hardware store or home improvement shop and get the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.