• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window panel replacement is a nuisance. This can be an opportunity to upgrade your windows to energy efficient or insulated ones to enjoy advantages like improved comfort, increased resale values and lower utility costs.

You can do it yourself for less than what it would cost to hire an expert. You'll only require the right tools and a few minutes of your time.

Glass

Replace your single-paned windows with tempered insulation glass to improve energy efficiency, cut down on noise, and maintain the historical integrity of your older home. The procedure of replacing the window pane is simple and can be done by anyone with basic hand tools. In addition to a replacement pane, the following tools are needed for the replacement process: latex glazing putty pliers, glazier's points and the use of a heat gun to warm the old putty if required. Wear safety glasses and gloves before you begin. Working with broken glass replacement for windows (https://willysforsale.com/) can cause serious injuries.

Take out any broken glass pieces remaining. It is best to use pliers for this, but a flathead can be used equally. Use a wood chisel, or putty knives, to take away any old putty remaining around the frame and the window sash. Be careful to not break the window sash. Be careful and slow. It is recommended to work using a sturdy ladder rather than the ground and have someone standing below the sash in order to help hold it steady.

Make sure that the window frame is ready to receive the new pane after you have removed the old putty. Measure the width and height of the opening in the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Take these measurements to the nearest hardware store or home center and find a piece glass cut to size. You can cut the glass yourself if you have the appropriate tools.

After installing the glass, apply caulking to the edge. This will make the glass weatherproof. Then install a glazier's point on each side of the frame to secure the pane in its place. The points should not be so tight as to cause friction between the sash and the frame, but they also should not be too loose.

Before putting the putty on, make sure to knead it until it is soft and free of lumps. Make it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from corner to corner, making sure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular metal pieces that help secure the glass into the window frame without causing any damage to the fragile surface. Understanding how to use these tiny pieces of help is simple and can save you money on a professional installation or the cost of new glass window replacement.

After the old putty and glazier's points are removed, thoroughly clean the frame with a knife to eliminate any remaining residue. Lightly sand the wood into the rabbet grooves to smooth out rough areas. If you do sand your wood, be sure to protect it with painter's tape to avoid accidental damage.

Measure the empty frame's dimensions and note down precise measurements. These measurements can be taken to a home center or hardware store and the new pane will be cut to a smaller size. This will ensure that the pane fits snugly and allows for expansion and contraction.

Place the new pane in the frame and press it down with your hands. Then, you can use the point of your chisel or the back of the putty knife to tap in the glazier's facets, as shown in Figure 11. When you're done taping, they should be level with the top edge of the pane, and the shoulders that are raised of the points should be just below the rabbet's rim groove.

Apply a thin layer of glazing compound on the rabbet grooves as well as the edges of the new glass. This will seal and protect the edges. Allow this to dry and cure fully.

When the glazing compound is dry and the glazing compound is dry, you can install the new window sash. The first step is to coat the wood with a heavy coat of Linseed oil. This will stop the new putty from sucking up the moisture and drying out and cracking with time. Apply this coat using a brush or the tip of your putty knife, then use the chisel or the back end from the putty knife to gently press the new sash and glazier's point into the grooves of the rabbet. Repeat this process every 10 inches around the perimeter of the frame.

Putty

A baseball thrown at you, an errant rock or falling branch could cause a window pane to crack or break. Luckily, most windows can be easily replaced by simply putting a brand new piece of glass in its the proper place. The glass is held in place using a small metal clip called the glazier's pointed and putty, also called glazing compound. Before installing a new pane, first remove the old one and clean the area with a rag and an abrasive scraper that is a pull type or a wood chisel. Wear safety glasses and gloves while doing this work. You'll need a heat gun in the event that the window is glued to the frame.

If you are planning to replace your original sash, you must remove the molding that holds the old pane. Then you can sand the sash down to ensure it's smooth and ready for new caulk. After the sash has been re-installed, apply a new silicone caulk around the glass to ensure that it won't leak or discolor in time.

Take the glazing points out of the rabbets, the grooves in the sash, where the glass sits. If they're difficult to cut out, try placing a hand tool like a heat gun to soften them first. When using a heating tool, be sure to not scratch the sash and its railings.

Once the old points of glazing and putty have been removed, prepare a bed for the new pane. Roll a piece of glazing compound between your hands, shaping it into a 1/2-inch thick. Then, press it into the rabbets in which the glass will rest. The glass must rest against the putty on both sides. If needed you want to tap your glass lightly into the rabbet using your thumb.

If the new pane has cracked, you can apply a silicone caulk or a glass glue made from solvents to seal the crack prior to pressing it in the sash. If not, you'll have to apply putty over the crack to create a tight seal and keep water out. After the putty has dried clean the oily film from the glass and let it dry completely before painting. If you paint before the putty is completely dry, it won't create an effective seal and could leak or discolor over time.

Paint

You might be worried about replacing a broken piece of glass. But the truth is that replacing a single glass pane doesn't require a huge amount of money if you do it yourself. In fact even windows with double panes can be replaced for less than the cost of a professional.

First, if you are working on a large-sized window, make sure that it is securely fixed to the frame. This job is relatively easy and fast using the appropriate tools and techniques.

When you are ready to start with the removal of the window pane. Pry out the metal glazing points attached to it. These are basically small metal triangles which function as "nails" that keep the window screen replacement in place in the wood frame. They are placed under a glaze putty or bead that hardens to solid wedge that holds the frame in place and conceals the edges.

After removing the old pane, clean the frame and wood. Scrape off any paint and sand down the rabbet grooves, where the glazing points were. These should be sanded to the point of being bare, so that you can paint them the same color as the rest the frame. After sanding the wood, apply a layer of flax oil. This will help to extend its life.

The next step is to measure the dimensions of the window opening. You will need to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you get the exact measurement for the new pane. This will allow for seasonal changes in the glass. You can take these measurements to a hardware store or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.