• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is a quick and cheap way to improve your home security. However, this process is not for all. It requires a certain amount of patience and expertise.

You need to replace the cylinder, which is located within the knob's body. The cylinder is what identifies the key once it's inserted into the lock.

Removing the old lock

The first step to replace a door lock is to remove the lock that was previously in use. It's a relatively easy process, but you should keep certain things in mind. First, ensure that the lock you choose to install is the right size for the door you have. This will ensure that it fits snugly and does not leave a gap around the latch or deadbolt plug.

After you have removed the latch plate, you'll need to look for two screws or bolts on the inside of the casing that hold the casing to the two halves of the lock. Take these screws off using a screwdriver and then pull the lock from the door. If you are using a mortise locking system, there is a set screw that holds the handle to the spindle. Use a screwdriver to unscrew this screw, then remove the doorknobs.

You must also remove the latch and deadbolt plug from the hole in your door jamb. Then, you can install your new lock. If you're replacing a mortise you must measure the distance between your lock case and your door edge to make sure that the new lock will fit.

There are a variety of reasons that could prompt you to change your door lock, such as being concerned that someone else may have the key, or you are welcoming the arrival of a new roommate. In any event, you could save money by taking the lock off yourself instead of paying an expert to remove it. The process is simpler than most people think, and it can be completed in just a few minutes.

Remove the handle and trim of your door. With a flat screwdriver, take off the trim. You should be able to twist off the majority of it. In some cases you may be able to remove the handles completely. Next, examine the handle for a small pinhole on the inside and insert a straightened paper clip into it. This will activate the release mechanism, which allows you to remove the handle. Then, look for another small tab on the interior of the lock, and press it with a flat screwdriver. Once the spindle has been removed, you can then take off the cylinder and housing.

The choice of a new locking system

When it comes time to pick the right lock for your home there are a lot of choices. Take a look at various types of locks and select one that fits your door's style. Take into consideration the backset (the distance between the door's edge and the center of the upvc window lock mechanism replacement hole) and the cross bore (small hole along the edge of the door frame). Select a lock that will fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give an idea of their durability and how difficult it is to pick them or disable them. A grade 3 lock might be a good choice for a tranquil rural apartment complex, while the grade 1 lock may be more able to withstand the traffic that is frequented by a retail storefront on a busy street.

Most smart door upvc window lock repair cost windows locks repair; http://bbs.01bim.com/, require digital code to open. If you are concerned about hacking or other security concerns, consult an expert locksmith.

Replace the cylinder

It is easy to replace damaged or broken door lock cylinder with a simple DIY project. It is crucial to choose the right cylinder and follow the instructions. The first step is to take off the knob or handle in the event that one is present then loosen the trim that is attached to the base of the lock cylinder by using the aid of a screwdriver. Once the trim has been removed, you can remove the screws that hold the cylinder in position with the flathead. The cylinder is then gently removed away from the door.

Before installing the new cylinder, be sure that it is the correct length for your door. Find the distance from the center to the right and left sides of the cylinder using the aid of a tape measure. Then, you can purchase another cylinder that has the same measurements. This will prevent cylinders from snapping when doors are kicked or the key becomes stuck inside.

Place the replacement cylinder inside the door, and then turn the key. This will align the cylinder with the carrier which is located usually on the outside of your lock. You can then loosen the set screws that should be a couple of turns in the head. You will also need to loosen the screw in the edge of the door that holds the case in place, in the event that there is one.

You can replace the cylinder that was used to lock your old lock with the new one by sliding it into the case, and tightening the set screws. The process of reinstalling the component that connects a cylinder to an indicator stem for a lock is also important. This can be done by pulling three small tabs on the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the back of the cylinder. Then, you must put back in the strike plate and latch plate as well as the retaining ring that is connected to the top lock cylinder.

Installing the new lock

If you're replacing a previous lock, you must begin by taking measurements of the width of the door. Most residential locksets are designed to fit a door thickness of 1 3/8 to 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll require a thicker door kit. This will include longer screws, or an extended spindle extension or the tail piece for door knobs.

The majority of locks come with a comprehensive installation guide to help you. Take the time to read the instructions before starting the process to ensure that you've followed all of the necessary steps. The guide will give you a clear idea of the level of skill that is required to finish the task. If you're replacing a lock for the first time, you might need to seek out an experienced person for help.

Before installing the new lock it's a good idea to cover the holes with tape the old hardware. This will prevent the screws from slipping out of the holes and will protect any tile you might have installed in the area. It also helps prevent possible damage caused by rust, grime, dirt and. SECURAM Touch comes with a strip of painter's tape that is intended to be used for this purpose, but you can also use gaffer's or masking tape if you have it available.

After removing the screws that hold the lock's interior half to the exterior and remove the lock immediately. It is important to do this quickly to avoid the lock from closing accidentally and damaging the mechanism.

Install the new latch bolt in the upper cross bore of the new double glazing window lock replacement, if it has one. Make sure you place it in the correct place that is usually indicated by an arrow on the faceplate. Then, place the latch plate on top of the bolt and secure it in place.

Finally, screw the deadbolt and strike plate to the door jamb. Try the deadbolt a few times by throwing it to make sure it extends into the strike plate. Follow the steps included with your electronic smart lock to program it. This involves downloading an application, registering your email address, confirming your identity, and then connecting to the wireless network to connect your device.