• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive method to increase the security of your home. However, the procedure isn't for everyone. It requires a certain amount of skill and patience.

The cylinder is contained within the knob's body. The cylinder recognizes the key when it is inserted into the lock.

Remove the old lock

The first step to replace a door lock is to remove the old one. It is a fairly easy process, but you should keep a few things in mind. Make sure that the new lock fits the door. This will ensure that it fits securely and does not leave a gap around the latch or deadbolt plug.

After you have removed the latch plate, look for two bolts or screws on the inside of the casing that hold the casing and the halves of the lock together. Remove these screws using the help of a screwdriver, and then remove the lock off the door. If you have a mortise locking system there is an anchor screw that connects the handle to the spindle. Remove the doorknobs by unscrewing the screw using a screwdriver.

Take the deadbolt and latch plug from the door jamb. Then, you can put in your new lock. If you're replacing a mortise, you should determine the distance between your lock case and your door's edge to ensure that the new lock will fit.

You might want to change your lock for various reasons, for instance, if you suspect that someone else is holding the key or if you've a new roommate. You can save money by deciding to take the lock off yourself, instead of hiring for a professional. The process is simpler than many people imagine, and it can be completed in a few minutes.

Begin by taking the trim and handle from your door. Then, pry the trim off with a flat screwdriver. You will be able to pull off most of it, and in some cases, the handles might come off entirely. Then, check the handle for a tiny pinhole on the interior side and insert a straightened paper clip into it. This will activate the release mechanism and allow you to take the handle from the door. Then, look for another small tab that is located inside of the lock, and press it with a screwdriver that is flat. After the spindle has been removed, you are able to remove the cylinder and the housing.

The choice of a new locking system

When it comes to choosing the right lock for your home, you have many options. Consider different kinds of locks, and select one that fits your door's style. Think about the backset which is the distance between the edge and the center of the hole in the lock. Also, consider the cross bore, a tiny hole that is located at the edge of your door frame. Select a lock that is suitable for the door thickness and the swing.

The American National Standards Institute and BHMA have graded all door Upvc windows locks repair to give an idea of their durability and the difficulty to pick them or disable them. A grade 3 lock may be the best choice for a peaceful rural apartment complex, while the grade 1 upvc window lock repairs may be more able to withstand the traffic that is frequented by a retail storefront on a busy street.

Most smart door locks require a digital key code to open. If you're worried about hacking, or any other security issues, talk to a professional locksmith.

Replacing the cylinder

It is easy to replace damaged or broken doors repair window lock cylinder with a simple DIY project. The key is to choose the correct cylinder and follow the directions that accompany it. First, you must remove the knob or handle if it is present. Then, using a screwdriver, remove the trim that is around the lock cylinder. Once the trim has been removed, it is possible to remove the screws holding the cylinder in position with a flathead. The cylinder is then gently pulled from the door lock window repairs.

Before installing the new cylinder, be sure it's the correct length for your door. With a tape measure, measure the distance between the cylinder's center and the left and right sides. Purchase a new cylinder that has the same measurements. This will prevent the cylinder from snapping, which could happen when the door is kicked out or when the key is stuck inside.

Insert the replacement locks for double glazed windows cylinder in the door and then turn the key. This will align the cylinder with your carrier which is typically on the outside of your lock. Then, loosen the set screw that should be a few turns inside the head. Also, you will need to loosen the screw at the door's edge which secures the case should there be one.

After you have removed the lock cylinder after which you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. Installing the part that connects the cylinder to a lock indicator stem is also important. It is done by pulling three small tabs at the back of the cylindrical with needle-nosed pliers. Attach the bracket that is smaller to the cylinder's back. Then, you must reinstall the strike plate and latch plate as well as the retaining ring that is connected to the top of the lock cylinder.

Installing a new lock

If you're replacing a previous lock, you must begin by measuring the width of your door. The majority of residential locksets come with a thickness of 3/8 to 1 3/4 inches. If your door is more thick you will require a thick door kit that includes longer screws as well as a longer tail piece (for door knobs) or spindle extension (for deadbolts).

The majority of locks come with a detailed instruction manual to assist you in installing the new hardware. Before you begin, read the instructions to ensure that you've followed all the steps. The guide will also give you an idea of the level of expertise required to perform the task. You may want to seek out a friend who has worked with locks for assistance if are changing locks for the first time.

It's a great idea to cover the holes in the old lock before installing the new lock. This will stop the screws from slipping through the holes, and also protect any tiles you might have put in. It also protects against potential damage from rust, dirt, and grime. SECURAM Touch includes the masking strip or gaffer tape. However, you can use any tape you have.

Once you've removed the screws that hold the inside of the lock section to the exterior side immediately, pull it back. It's crucial to do this as quickly as possible to prevent the lock from accidentally closing on itself and damaging the mechanism.

If your new lock is equipped with an latch bolt, install the new latch bolt into the upper cross bore. Make sure you put it in the correct position, which is indicated by an arrow. Then, screw the latch plate onto the bolt.

Finally, screw the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it a several times to make sure that it extends all way through the strike plate and is completely secure. Follow the steps included in your electronic smart lock to program it. This involves downloading an application, creating an email address, confirming your identity, then accessing the wireless network to connect your device.