• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

It's easy to repair a damaged window handle using the appropriate tools. It is essential to identify the kind of handle you have and its spindle size before you purchase an alternative.

Older uPVC window handles have a spur which extends and is locked over the wedge striker for cockspur. These can be left- or right-handed and should be matched when replacing.

What type of lock and handle do I have?

There are a myriad of upvc window locks and handles each with their own advantages and purposes. The type of handle you choose will determine whether or not your locking mechanism is efficient and also if it is simple to open the windows. With time and regular use, the upvc handles on your windows could get worn out and damaged. This makes them less secure and effective. In some cases they may even fall completely off. If you notice that your upvc window handles have fallen off, it's crucial to fix them as soon as you can. This will prevent possible break-ins and ensure that your home is safe.

The good news is that replacing your window handles made of plastic is a simple task that is achievable by nearly everyone. You'll need a few tools, but with the proper knowledge, it's a straightforward process that should only take a few minutes. It is important to know the type of lock or handle you have on your window. This will allow you to choose the right replacement.

Inline Espagnolette Handles

They are usually found on the side of the window. They are flat and come with an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles have a spindle that runs through the middle of the handle to the window replacement near me frame to control the latch.

Cockspur Handles

They are typically found on older uPVC window frames and have distinct hook-shaped designs. Cockspur handles are attached to the window frame by a single screw and are less secure than other types of window handles.

Tilt and Turn Handles

The tilt and turn handles differ from other upvc handles because they can be turned to open the window and then lowered into the window to ventilate. In general, they have a 7mm spindle on the back of the handle and are available in left and right-handed versions.

When purchasing replacement windows handles made of upvc It is crucial to check the spindle length as not all are the same size. Drop something in the middle of the hole to measure the length. This is the largest spindle size that will fit your windows.

What is the spindle?

uPVC window handles work similarly like doors, turning the handle to activate an internal latch within the frame. The window can then be opened and shut. But, at times, these handles can become damaged, especially when they are used frequently or exposed to harsh weather conditions. This can leave you needing to replace your uPVC windows handles as they might not operate the window correctly for a long time.

There are a variety of uPVC handles available including Espag, Cockspur and Spaded handles. They are made in a variety of ways to fit into uPVC frames. Each handle type uses a different spindle to lock the window mechanism. This is why it is crucial to know the kind of handle you have on your uPVC window so you can find the right replacement window near me.

The base of the handle will tell you what kind of uPVC it is. There should be a "snap-in cover' over one screw which holds the handle base in the correct position. Take it off and you should be able to see the second screw located at the opposite end of the base section of the handle. Once both screws have been removed then you should be able to take the handle out of the uPVC.

Once you have removed your uPVC window handle, you will need to carefully unscrew the old spindle from the locking mechanism. Take note of the length of the spindle. You'll need purchase a new one that is the same length as the original handle and the locking device.

The spindle wears down and is unable to operate the locking mechanism. This could be due to damage from constant use, a loosening of the locking mechanism, or even corrosion over time. If this happens, you will need to replace both the window handle and the locking mechanism to restore the full functionality of your uPVC Windows.

How do I take off the old handle?

Window handles are susceptible to being damaged or even broken over the course of time. It is crucial to fix them as quickly a possible to ensure your security. It is easy to replace a damaged or worn handle. The task can be completed in less than a minute without the need for special tools.

To take off the handle, you first need to remove the screw that is located at the base of the handle. Once the screw is removed, the handle can be pulled away. There will be another screw located at the bottom of the handle's base, and it is able to be removed as well. When both screws are removed, the handle can be completely detached from the base section of the window.

Once the old handle has been removed, you can take the new handle and align the fixing holes with the holes that are present in the window frame. There may be a tiny sticker or caps on the new handle, so take off them if needed and then put the handle in its place. It is important to check that the handle is working after it is installed. Turn the handle around and make sure that the lock mechanism is in place.

Espag handles come with an elongated spindle that extends from the handle and slots into a multipoint locking mechanism in the window frame. Cadenza windows have a blade with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that is able to hook over the frame's outer or the transom bar cross member inside the window.

Once you have the new handle in place, insert the spindle inside the lock in the window and then tighten it down. Once the handle is firmly fixated, replace the'snap in' cover and the screw cap (if applicable). When the handle is in use, simply open and close the window a couple of times to make sure that it functions properly and securely.

How do I install the new handle?

Changing your uPVC window handle isn't difficult, and the process is simple. All you need is a screwdriver and little bit of patience. The first step is to ensure that the old handle is in the unlocked position and then remove any screws that are visible, you can also replace these by screw caps if you need. Once the handle is removed, you need to make an outline of the length of the spindle that protrudes from the back of the handle. This is vital because it will determine the kind of handle to purchase.

Espagnolette handles that are made of uPVC are the most well-known kind of handle. They feature a spindle that is connected to the handle and operates a locking mechanism inside the window frame. The handle releases the latch and allows the window to open. With time and regular use, espagnolette handles could be damaged or destroyed which is why it is essential to locate replacements.

Cadenza handles are a type of uPVC handle that is usually employed with tilt and turn windows. They have an extended blade that works an interlocking mechanism that is multipoint within the window. They are more secure than an espagnolette handles because they are able to open from the inside. They can be replaced using the same method as you would do for handles made of espagnolette however, make sure that the new handle is not angled and flat.

After you have chosen the correct handle, simply align the new handle with the existing screw holes before screwing it in place. Then, you should put the screw covers on and test the new handle. You can do this by moving the handle between the locked position to the unlocked one a few time. It may be worth contacting an expert to determine how you can fix any problems. They are often able to advise you on the best approach to resolve the issue in a quick and effective manner.